Skip to main content

Raspberry Pi Controlled robot from junk


In previous posts I start looked at using ScratchGPIO to control a junkbot - more about junkbots can be found at:http://junkbots.blogspot.com

Previous Posts:
 (http://junkbots.blogspot.com/2014/08/junkbot-pi-1-scratchgpio.html) and showed a Pi controlled junkbot briefly in action (http://junkbots.blogspot.co.uk/2014/08/junkbot-raspberry-pi-2-raspberry-pi.html).

In this post I aim to discuss
- Choice of motor controller card
- Provide an example of a drawing junkbot controlled through Scratch and Raspberrry Pi


Choice of interface/Controller card
The card chosen was the 4Tronix PiRoCon card  (http://4tronix.co.uk/store/index.php?rt=product/product&product_id=182). Selected for four reasons
- Price is reasonable (in my opinion).
- Fits straight onto the Pi through the GPIO - no extra cables needed.
- ScratchGPIO has it as an addon so it makes programming it even easier (see http://cymplecy.wordpress.com/2013/10/31/pirocon-from-4tronix/).
- Others are using it for robot projects.

Use it is quite easy plug the board directly on to the GPIO connector of the Raspberry Pi (4tronix provide some advice in section 15 of http://4tronix.co.uk/blog/?p=22 on mounting the board). The only other changes I needed to make because I wasn't powering the motors through the DC input I had to change the jumper settings next to Vin Connector (see http://4tronix.co.uk/blog/?p=41 for layout) to reflect this.



Example
Now for the fun bit get the whole thing to draw (see Figure 1 and the video at the end)!

The junkbot itself is made up of a drinks can, three supports (we used LEGO here but it equally could be straws, sticks), a pen/pencil, and a  motor and broken propeller combination to create an unbalanced motor.

With the Raspberry Pi off, the the motor's wires are connected to the controller card at the connections for MotorA and the battery is also connected. Turn the Pi on and run ScratchGPIO5plus.


Figure 2
Figure 3





Figure 4















The first task is to make the variables AddOn (which will be used to tell the program we are using the PiRoCon card) and MotorA for the motor (see Figure 3).

In Figure 4 the program can be seen, essentially the left and right key spin the junkbot clockwise or anticlockwise by setting the Motor to either +ve or -ve values from 0 to 100. The space bar is used to stop the motor.

As it moves because one of the supports is a pen it draws. See the video below to watch it draw a squiggly line - control is still a challenge.

 
The bot was developed by Hayden Tetley and Scott Turner. Hayden's time was paid  for through the Nuffield Research Placements  Scheme (http://www.nuffieldfoundation.org/nuffield-research-placements).

Related Link

 




If you would like to know more about the Junkbots project contact scott.turner@northampton.ac.uk. The views and opinions is the authors and should not be taken as representing the views of any organisation the author is associated with.



All opinions in this blog are the Author's and should not in any way be seen as reflecting the views of any organisation the Author has any association with.

Popular posts from this blog

Micro:bit, Servo control with Micropython or blocks

You can control servos (small ones) from a Micro:Bit directly. Following a link from the David Whale (Twitter ) , thank you, took me to a Kitronik blog post, https://www.kitronik.co.uk/blog/using-bbc-microbit-control-servo/, which has the answer.

The code uses Microsoft Blocks taken from the post, runs the servos 180 degrees and back again, when button A is pressed. It does exactly what it should. I am also using the Tower Pro SG90 servo.
Can it be replicated in Micropython? This is a new mini project, there seems to be little out there yet on how do this but the best so far is this video by PHILG2864:



The closest I have is the following, it is essentially there.
from microbit import *
pin0.set_analog_period(20)
while True:
    pin0.write_analog(180)
    sleep(1000)
    pin0.write_analog(1)
    sleep(1000)

Setting the time period to 20ms  pin0.set_analog_period(20)seems by experiment (and used in the video above) to be best value so far. The reason for pin0.write_analog(1)  set to 1 i…

LittleBits Star Wars Droid and Swift Playgrounds

On the 1st September 2017, during 'Force Friday', LittleBits launched their new kit Star Wars Droid Inventor Kit an R2D2 shaped robot, though you are encouraged to customise it to form your own designs. It comes a number of tutorials, that take you through building a moving head, a proximity sensor to move away from you, and many others.


So confession time, I am not the target audience for this kit, but I have enjoyed playing with it. The tutorials take you through building and dismantling the kit, doing a range of different activities and in most cases controlling it remotely from an iPad. You can even record your voice and have it played back from the Droid, in my opinion, the wide of sounds is one of the things that lift this from being just a nice kit -  I will get onto the other one soon. Though good fun, I was left with a question can it be programmed?

This was my first time using a LittleBits kit I didn't know what the options were available for programming it, a quic…

my robot BETT2017

I will start with a confession, I only had about 2 1/2 hours at BETT 2017 due to external time pressures so to say I didn't yet a chance for a good (or even a bad) look around is an understatement; so I am not reviewing the show just a few notes on what I did manage to see.


STEAM Village
First and mostly, it was great to talk to so many people, only few I had met face to face previously, about robots, micro:bits, Raspberry Pis and coding. Most of this happen in the relatively small (compared to the event space) STEAM village and nearby stalls. It was great to see the strong presence of both Raspberry Pi and Micro:Bit Foundation, along the variety of different activities and example usage of both, with Code Club (I know it is part of Raspberry Pi Foundation) there was well. This was all alongside some other companies

Four of these stuck in my mind.

1. DFRobot (https://www.dfrobot.com/) with their range of Arduino-based robots and non-programmable kits. The two kits that caught my eye w…