Skip to main content

USB Robot arm control with Python and Raspberry Pi

I was asked recently if the USB robot arm could be programmed - I knew the answer was yes. The Arm came from the CBiS Education Robot Arm kit (http://www.cbis.education/Product-Details.aspx?prodid=2 ) which comes with a Raspberry Pi and SD Card with software to control the Arm. So the question has become - How do I program it in Python from scratch?

Well, the honest answer is I don't I use what others have done before. A good 
starting point is this site http://www.wikihow.com/Use-a-USB-Robotic-Arm-with-a-Raspberry-Pi-(Maplin), it gives most (pretty much all) of the answer, including where to get the pyusb library need; setting it up (be careful don't use the  zip file but the tar.gz version  - you might need to scroll down the screen to do this) and an example. A second source that was very useful was  http://notbrainsurgery.livejournal.com/38622.html?view=93150#t93150 which contains an explanation of the 'triples' (for example [32,0,0]) used to select which part of the arm moves and what it does (in the example [32,0,0] causes the Robot Elbow to move down).


The code below is largely based on the code in http://www.wikihow.com/Use-a-USB-Robotic-Arm-with-a-Raspberry-Pi-(Maplin) the only real changes are named procedures (such as ElbowUp) in place of the slightly less easy to understand lines such as  MoveArm(Duration,[4,0,0]) #wrist up . The only other changes was a procedure that changes what the light does (0 - light off; 1 - light on; 3 - pulses by a number of times).

import usb.core, usb.util, time
RoboArm = usb.core.find(idVendor=0x1267, idProduct=0x000)

if RoboArm is None:
    raise ValueError("Arm not found")

Duration=1
#Define a procedure to execute each movement
def MoveArm(Duration, ArmCmd):
    #Start the movement
    RoboArm.ctrl_transfer(0x40,6,0x100,0,ArmCmd,3)
    #Stop the movement after waiting a specified duration
    time.sleep(Duration)
    ArmCmd=[0,0,0]
    RoboArm.ctrl_transfer(0x40,6,0x100,0,ArmCmd,3)

def RotateBaseClockwise(Duration):
    MoveArm(Duration,[0,1,0]) #Rotate base clockwise

def RotateBaseAntiClockwise(Duration):
    MoveArm(Duration,[0,2,0]) #Rotate base clockwise

def ElbowUp(Duration):
    MoveArm(Duration,[16,0,0]) #Elbow up 0x10

def ElbowDown(Duration):
    MoveArm(Duration,[32,0,0]) #Elbow down 0x20

def WristUp(Duration):
    MoveArm(Duration,[4,0,0]) #wrist up 0x04

def WristDown(Duration):
    MoveArm(Duration,[8,0,0]) #wrist down 0x08

def CloseGripper(Duration):
    MoveArm(Duration,[1,0,0]) #close gripper 0x01

def OpenGripper(Duration):
    MoveArm(Duration,[2,0,0]) #open gripper 0x02

def ShoulderUp(Duration):
    MoveArm(Duration,[64,0,0]) #shoulder up 0x40

def ShoulderDown(Duration):
    MoveArm(Duration,[128,0,0]) #shoulder down 0x80

def GripLight(Action, Duration):
    if (Action==1):
        MoveArm(Duration,[0,0,1]) #light on
    if (Action==0):
        MoveArm(Duration,[0,0,0]) #light off
    if (Action==3):
        for x in range(Duration):
            MoveArm(1,[0,0,1]) #light on
            MoveArm(1,[0,0,0]) #light off

WristUp(0.5)
OpenGripper(0.5)
RotateBaseClockwise(2)
RotateBaseAntiClockwise(2)
ElbowUp(1)
ElbowDown(1)
WristDown(0.5)
CloseGripper(0.5)
ShoulderUp(3)
ShoulderDown(1)
GripLight(3,3)


See it action in the video below.








All opinions in this blog are the Author's and should not in any way be seen as reflecting the views of any organisation the Author has any association with.

Popular posts from this blog

Micro:bit, Servo control with Micropython or blocks

You can control servos (small ones) from a Micro:Bit directly. Following a link from the David Whale (Twitter ) , thank you, took me to a Kitronik blog post, https://www.kitronik.co.uk/blog/using-bbc-microbit-control-servo/, which has the answer.

The code uses Microsoft Blocks taken from the post, runs the servos 180 degrees and back again, when button A is pressed. It does exactly what it should. I am also using the Tower Pro SG90 servo.
Can it be replicated in Micropython? This is a new mini project, there seems to be little out there yet on how do this but the best so far is this video by PHILG2864:



The closest I have is the following, it is essentially there.
from microbit import *
pin0.set_analog_period(20)
while True:
    pin0.write_analog(180)
    sleep(1000)
    pin0.write_analog(1)
    sleep(1000)

Setting the time period to 20ms  pin0.set_analog_period(20)seems by experiment (and used in the video above) to be best value so far. The reason for pin0.write_analog(1)  set to 1 i…

LittleBits Star Wars Droid and Swift Playgrounds

On the 1st September 2017, during 'Force Friday', LittleBits launched their new kit Star Wars Droid Inventor Kit an R2D2 shaped robot, though you are encouraged to customise it to form your own designs. It comes a number of tutorials, that take you through building a moving head, a proximity sensor to move away from you, and many others.


So confession time, I am not the target audience for this kit, but I have enjoyed playing with it. The tutorials take you through building and dismantling the kit, doing a range of different activities and in most cases controlling it remotely from an iPad. You can even record your voice and have it played back from the Droid, in my opinion, the wide of sounds is one of the things that lift this from being just a nice kit -  I will get onto the other one soon. Though good fun, I was left with a question can it be programmed?

This was my first time using a LittleBits kit I didn't know what the options were available for programming it, a quic…

my robot BETT2017

I will start with a confession, I only had about 2 1/2 hours at BETT 2017 due to external time pressures so to say I didn't yet a chance for a good (or even a bad) look around is an understatement; so I am not reviewing the show just a few notes on what I did manage to see.


STEAM Village
First and mostly, it was great to talk to so many people, only few I had met face to face previously, about robots, micro:bits, Raspberry Pis and coding. Most of this happen in the relatively small (compared to the event space) STEAM village and nearby stalls. It was great to see the strong presence of both Raspberry Pi and Micro:Bit Foundation, along the variety of different activities and example usage of both, with Code Club (I know it is part of Raspberry Pi Foundation) there was well. This was all alongside some other companies

Four of these stuck in my mind.

1. DFRobot (https://www.dfrobot.com/) with their range of Arduino-based robots and non-programmable kits. The two kits that caught my eye w…